Ajax · Alarmă · Fire detectors

FireProtect 2 SB (CO) Jeweller – specificații și firmware

FireProtect 2 (CO) Jeweller

Ajax nu publică un fișier de firmware pentru acest model.

Înainte de actualizare: verifică pe eticheta aparatului modelul exact și versiunea hardware și folosește firmware-ul din regiunea aparatului (de exemplu Global sau Europa). Un firmware greșit poate bloca aparatul. Nu întrerupe alimentarea în timpul actualizării.

Ajax FireProtect 2 SB (CO) Jeweller este o componentă de sistem de alarmă, listat de producător la „Fire detectors”.

Producătorul îl prezintă ca „FireProtect 2 (CO) Jeweller”. Fizic, cântărește 147 g și are dimensiunile 44 × 86 × 86 mm.

Pentru FireProtect 2 SB (CO) Jeweller, Ajax nu oferă un fișier de firmware descărcabil. Mai jos scrie cum se actualizează.

Mai jos găsești fișa tehnică completă, tradusă în română.

Cum se actualizează FireProtect 2 SB (CO) Jeweller

Ajax nu publică fișiere de firmware; actualizarea se face prin hub/aplicația Ajax.

Ajax nu publică fișiere de firmware: dispozitivele se actualizează automat prin hub, iar hub-ul primește noile versiuni OS Malevich prin internet, fără intervenția utilizatorului.

Dacă producătorul publică pe viitor un fișier de firmware pentru acest model, îl adăugăm automat pe această pagină.

Specificații FireProtect 2 SB (CO) Jeweller

Variante

FireProtect 2 RB (CO) Jeweller	FP2.RBC.J — specificațiile de mai jos
FireProtect 2 SB (CO) Jeweller	FP2.SBC.J

Comunicație

Tehnologie de comunicație Jeweller	Proprietary wireless technology for transmission of alarms and events. Features: - Two-way communication. - Protection against device spoofing. - Block encryption featuring a floating key. - Instant notifications. - Remote configuration via the Ajax apps.
Radio frequency bands	866.0 – 866.5 MHz 868.0 – 868.6 MHz 868.7 – 869.2 MHz 905.0 – 926.5 MHz 915.85 – 926.5 MHz 921.0 – 922.0 MHz Depends on the region of sale.
Putere maximă radiată (ERP)	Până la 20 mW Automatic power control to reduce power consumption and radio interference.
Modulație semnal radio	GFSK
Rază de comunicație radio	Până la 1,700 m Between the detector and a hub (or radio signal range extender) in an open space.
Encryption of radio communication	All the data stored and transmitted are protected by block encryption with a floating key.
Radio frequency hopping	To prevent radio interference and jamming.

Carbon monoxide (CO) detection

Element sensibil	chemical CO sensor
Alarm if accumulated dose of CO is exceeded	more than 50 ppm (0.005%) — no more than in 90 minutes more than 100 ppm (0.01%) — no more than in 40 minutes more than 300 ppm (0.03%) — no more than in 3 minutes CO concentration of 400 ppm (0.04%) within 3 hours can be life-threatening. The detector stops notifying about the dangerous level of carbon monoxide when the concentration drops to 50 ppm (0.005%) within one minute.
Sensor life	10 years After 10 years of operation, the detector must be replaced with a new one.

Funcții suplimentare

In-built siren	volume 85 dB at a distance of 3 meters Sound notification of alarms. Active until the reason for triggering is eliminated or until the user disables notification.
Interconnected fire detectors alarms	via primary interconnection If one of the fire detectors in the system detects a threat, it sends an alarm to the hub. Within 20 seconds, the hub initiates an interconnected alarm and sends data to Ajax apps. via fallback interconnection1 At the same time with notifying the hub, the initiating detector sends an alarm directly to other detectors. All connected detectors activate the buzzer within a minute. It will work even in the worst-case scenario of losing connection with the hub. 1 Fallback interconnected alarm is available only for FireProtect 2 detectors with firmware version 5.59.2.ХХ or later. Devices that support the fallback interconnected alarm are marked on the package with a “Fallback interconnect supported” label.
LED indication	green is a power indication A LED indicator on the device enclosure lights up once every 56 seconds. The indication meets the requirements of EN 50291. yellow is an indication of malfunctions A LED indicator on the device enclosure lights up when malfunctions are detected. For example, if the battery is low. red is an indication of fire alarms A LED indicator on the device enclosure lights up when the detector registers a fire alarm.
Button on the front panel of the detector	In normal mode, runs the detector test when pressed. In the event of an alarm or malfunction, the pressing turns off the detector sound notification.

Recomandări

	The device is designed only for indoor installation. SmartBracket mounting panel allows adjusting the position of the detector after installation.

Anti-sabotage protection

Tampering alarm	Alerts of attempts to detach the detector from the surface or remove the mounting panel.
Protecție anti-spoofing	Autentificare dispozitiv
Detection of communication failure	within 15 minutes The time to detect communication loss depends on the settings for the number of undelivered data packages (specified in the Jeweller or Jeweller/Fibra settings). The polling interval is fixed at 300 seconds.

Alimentare

For FireProtect 2 RB (CO)	2 × CR123A battery Până la 7 years of battery life.

Carcasă

Dimensiuni	44 × 86 × 86 mm
Greutate	147 g
Interval temperatură de funcționare	from 0°С to +50°С
Umiditate de funcționare	Până la 80%
Clasă de protecție	IP20

Culori

	Negru
	Alb

Conținut set

	FireProtect 2 RB (CO) Jeweller
	SmartBracket mounting panel
	Kit de montaj
	2 × CR123A battery (pre-installed)
	Ghid de pornire rapidă

Standarde și certificări

Electrical apparatus for the detection of carbon monoxide in domestic premises	EN 50291-1:2018 UkrTEST of SE “Ukrmetrteststandart”
Directiva RED	EN 300 220-1 V3.1.1 EN 300 220-2 V3.2.1 Certificate issued by MiCOM Labs
Directiva RoHS	EN IEC 63000:2018 Shenzhen NTEK Testing Technology Co.
Directiva EMC	EN 301 489-1 V2.2.3 EN 301 489-3 V2.1.1 Certificate issued by MiCOM Labs
Directiva de joasă tensiune (LVD)	EN 62368-1:2020+A11:2020 EN 62479:2010 Certificate issued by MiCOM Labs
ID IC	2AX5VFICOJ1 Certificate issued by MiCOM Labs
PSTI UK	Schedule 1

Compatibil cu

Hub (4G) Jeweller, Hub 2 (2G) Jeweller, Hub 2 (4G) Jeweller, Hub 2 Plus Jeweller, Hub BP Jeweller, Hub BP Jeweller (without casing), ReX 2 Jeweller, ReX Jeweller, Superior Hub G3 Jeweller, Superior Hub Hybrid (2G), Superior Hub Hybrid (4G), Superior Hub Hybrid (4G) (without casing), Superior Hub Hybrid 2, Superior Hub Hybrid 2 (without casing), Superior MegaHub, Superior MegaHub (without casing), Superior ReX G3 Jeweller

Specificațiile sunt cele publicate de Ajax, cu etichetele traduse în română (preluate la 02.11.2026). Ce nu am tradus a rămas în engleză.