Ajax · Alarmă · Fire detectors

FireProtect 2 AC (CO) Jeweller – specificații și firmware

Ajax nu publică un fișier de firmware pentru acest model.

Înainte de actualizare: verifică pe eticheta aparatului modelul exact și versiunea hardware și folosește firmware-ul din regiunea aparatului (de exemplu Global sau Europa). Un firmware greșit poate bloca aparatul. Nu întrerupe alimentarea în timpul actualizării.

FireProtect 2 AC (CO) Jeweller este o componentă de sistem de alarmă Ajax din categoria „Fire detectors”. Fizic, cântărește 304 g și are dimensiunile 122 × 122 × 54 mm.

Nu există un firmware public de la Ajax pentru FireProtect 2 AC (CO) Jeweller. Mai jos scrie cum se actualizează.

Specificațiile complete, cu etichetele traduse în română, sunt în tabelul de mai jos.

Cum se actualizează FireProtect 2 AC (CO) Jeweller

Ajax nu publică fișiere de firmware; actualizarea se face prin hub/aplicația Ajax.

Ajax nu publică fișiere de firmware: dispozitivele se actualizează automat prin hub, iar hub-ul primește noile versiuni OS Malevich prin internet, fără intervenția utilizatorului.

Dacă producătorul publică pe viitor un fișier de firmware pentru acest model, îl adăugăm automat pe această pagină.

Specificații FireProtect 2 AC (CO) Jeweller

Comunicație

Tehnologie de comunicație Jeweller	Proprietary wireless communication technology to transmit commands, alarms, and events. Key features: - Two-way communication. - Advanced anti-sabotage. - Block encryption featuring a dynamic key. - Instant notifications. - Remote configuration in the Ajax apps.
Benzi de frecvență	866.0 – 866.5 MHz 868.0 – 868.6 MHz 868.7 – 869.2 MHz 905.0 – 926.5 MHz 915.85 – 926.5 MHz 921.0 – 922.0 MHz Depends on the region of sale.
Putere maximă radiată (ERP)	Până la 20 mW Automatic power control to reduce power consumption and noise interference.
Modulație semnal radio	GFSK
Rază de comunicație radio	Până la 1,500 m Between detector and hub (or range extender) in an open space.
Comunicație criptată	All stored and transmitted data are protected by block encryption featuring a dynamic key.
Salt de frecvență	Radio communication uses frequency hopping to prevent interception and jamming.

Carbon monoxide (CO) detection

Element sensibil	chemical CO sensor
Alarm if accumulated dose of CO is exceeded	over 50 ppm (0.005%) — in 90 minutes or less over 100 ppm (0.01%) — in 40 minutes or less over 300 ppm (0.03%) — in 3 minutes CO concentration exceeding 400 ppm (0.04%) within a span of 3 hours poses a life-threatening risk. The detector will cease notifications regarding hazardous carbon monoxide levels once the concentration decreases to 50 ppm (0.005%) within a 1-minute duration.
Sensor service life	10 years After 10 years of operation, the detector must be replaced with a new one.

Funcții suplimentare

Built-in siren	volume 85 dB at a distance of 3 meters Sound notification of alarms. Remains active until the reason for triggering is eliminated or until the user manually disables the notification.
Interconnected fire detectors alarms	via primary interconnection If one of the fire detectors in the system detects a threat, it sends an alarm to the hub. Within 20 seconds, the hub initiates an interconnected alarm and sends data to Ajax apps. via fallback interconnection At the same time with notifying the hub, the initiating detector sends an alarm directly to other detectors. All connected detectors activate the buzzer within a minute. It will work even in the worst-case scenario of losing connection with the hub.
LED indication	green is a power indication An LED indicator on the device enclosure lights continuously when powered by an external power source. If the device draws power from the backup battery, the LED indicator lights up once every 56 seconds. This indication complies with the requirements stipulated in EN 14604 and EN 50291 standards. yellow is a malfunction indication An LED indicator on the device enclosure lights up to signal detected malfunctions. This can occur in instances such as battery depletion, smoke chamber contamination, or reaching the end of the service life. red is a fire alarm indication An LED indicator on the device enclosure lights up when the detector registers a fire alarm.
Button on the front panel of the detector	In normal mode, when pressed, it starts the smoke chamber test. In the event of an alarm or malfunction, the pressing turns off the detector sound notification.
External power supply	110–240 V~, 50/60 Hz The phase and neutral cables from the external power supply should be connected to the WAGO terminals on SmartBracket mounting panel. To remove the detector from SmartBracket, there is no need to disconnect the power cables.

Recomandări

	The device is designed for indoor installation only.
	SmartBracket mounting panel allows adjusting the position of the detector even after installation.

Protecție anti-sabotaj

Alarmă anti-sabotaj	Notifications on attempts to detach the detector from the surface or remove it from the mounting panel.
Protecție anti-spoofing	Autentificare dispozitiv
Detecție pierdere comunicație	within 15 minutes The time required to detect a communication loss depends on the settings for the number of undelivered data packages (specified in the Jeweller or Jeweller/Fibra settings).

Alimentare

Main	110–240 V~, 50/60 Hz Până la 2 W of mains power consumption.
Backup	1 non-replaceable lithium battery CR-2/3AZ Allows the detector to operate autonomously without the main power source.

Carcasă

Dimensiuni	122 × 122 × 54 mm
Greutate	304 g
Interval temperatură de funcționare	from 0°С to +50°С
Umiditate de funcționare	Până la 80%

Culori

	Negru
	Alb

Conținut set

	FireProtect 2 AC (CO) Jeweller
	SmartBracket mounting panel
	WAGO 221 3-conductor terminal — 2 pcs.
	(pre-installed in SmartBracket)
	Kit de montaj
	Ghid de pornire rapidă

Standarde și certificări

Electrical apparatus for the detection of carbon monoxide in domestic premises	EN 50291-1:2018 BS EN 50291-1: 2018 UkrTEST of SE “Ukrmetrteststandart”
Directiva RED	EN 300 220-1 V3.1.1 EN 300 220-2 V3.2.1 Certificate issued by MiCOM Labs
Directiva RoHS	EN IEC 63000:2018 Shenzhen NTEK Testing Technology Co.
Directiva EMC	EN 301 489-1 V2.2.3 EN 301 489-3 V2.1.1 EN 55032:2015+A1:2020 EN 55035:2017+A11:2020 EN IEC 61000-3-2:2019+A1:2021 EN 61000-3-3:2013+A2:2021 Certificate issued by MiCOM Labs
Directiva de joasă tensiune (LVD)	EN 62479:2010 EN IEC 62368-1:2020+A11:2020 Certificate issued by MiCOM Labs
BSI KITEMARK Carbon Monoxide Alarms	KM 797661 Certificate issued by BSI Assurance UK Ltd.
ID FCC	2AX5VFIACC1 Certification Issued Under the Authority of the Federal Communications Commission
ID IC	26860-FIACC1 Certificate issued by MiCOM Labs
PSTI UK	Schedule 1

Compatibil cu

Hub (4G) Jeweller, Hub 2 (2G) Jeweller, Hub 2 (4G) Jeweller, Hub 2 Plus Jeweller, Hub BP Jeweller, Hub BP Jeweller (without casing), ReX 2 Jeweller, ReX Jeweller, Superior Hub G3 Jeweller, Superior Hub Hybrid (2G), Superior Hub Hybrid (4G), Superior Hub Hybrid (4G) (without casing), Superior Hub Hybrid 2, Superior Hub Hybrid 2 (without casing), Superior MegaHub, Superior MegaHub (without casing), Superior ReX G3 Jeweller

Specificațiile sunt cele publicate de Ajax, cu etichetele traduse în română (preluate la 02.11.2026). Ce nu am tradus a rămas în engleză.